Design Calculations · DIN 509 undercut

DIN 509 undercut

Diameter, type and load → r, t1, t2, f, g and minimum countersink on the mating part

mm
The shaft diameter. For a bore: the bore diameter.
Common diameters

Fills in the diameter only.

Type
E: only the cylinder is machined afterwards (usually ground). F: the cylinder and the shoulder are both machined afterwards, so the mating part can sit flat against the shoulder.
Load
Higher alternating load: the load keeps changing. The standard gives sizes for this above Ø 18 mm.
—

Undercut dimensions

Minimum countersink on the mating part (a). The mating part (bearing, hub, bush) needs a chamfer or countersink of at least a on the shoulder side; the countersink diameter is at least d1 + 2a. Otherwise it touches the rounding of the undercut instead of the shoulder.

Source: DIN EN ISO 18388 (ISO 18388:2016); the same table appeared in DIN 509:2006-12.

About the source

The tolerances come from DIN 509:2006-12. The newer DIN 509:2022-12 sets them again; that text has not been checked. Tolerances from DIN 509:2022 not confirmed.

Inventor: Manage › Parameters, or straight into the dimension field of your sketch.

Section of a shaft with a shoulder and undercut, showing the dimensions r, t1, t2, f and g. f t1 gt2 r shaft
Undercut at the shoulder
Section of the mating part with chamfer a against the shoulder. a mating part shaft
Mating part with chamfer a

Schematic, not to scale.

Enter a diameter: the dimensions appear here.

The split by diameter does not apply to short shoulders and thin-walled parts. If a part has several diameters, you may use the same undercut at all shoulders.

The dimensions come from the standard and are meant as an aid. Always check your own drawing and the current standard. You remain responsible for your design.

Details: explanation, Inventor and sources

What is an undercut?

An undercut (ISO 18388 calls it a relief groove; also grinding relief; Freistich in German) is a small groove in the inside corner where a shaft steps down, or in a bore. The dimensions also apply to bores. Not to be confused with the thread undercut or run-out of DIN 76-1, which has different dimensions.

The grinding wheel or turning tool can work right up to the shoulder. The mating part (bearing, hub or bush) sits flat against it if it has its own chamfer or countersink of at least a (see below).

The standard has four types:

  • Type E: only the cylinder is machined afterwards; the shoulder is lightly loaded, or the mating part has a large countersink or does not touch the shoulder.
  • Type F: both the cylinder and the shoulder face are machined afterwards; the mating part can sit flat against it.
  • Type G: for indexable inserts, with a small transition; only for lightly loaded parts.
  • Type H: for indexable inserts, with a larger transition.

This page covers types E and F. The dimensions depend on the diameter and the load.

r is the radius of the rounding. t1 is how deep the groove goes into the cylinder. t2 is how deep it goes into the shoulder (type F only). f is the width of the groove along the axis. g is the width along the shoulder (type F only, a guide value). a is the minimum countersink on the mating part.

Load. For normal load, take the standard size. For higher alternating load (the load keeps changing, for example a rotating shaft in bending) the standard gives a larger radius, because a more generous rounding lowers the stress peak in the corner. These sizes only exist above Ø 18 mm. For Ø 18 mm and smaller the standard gives no size; the page then shows the size for normal load and says so. Notch effect under fatigue: see DIN 743.

Size. Sometimes two sizes fit your diameter. Take series 1 (the preferred radii: 0.4 · 0.8 · 1.2 · 1.6 · 2.5 · 4 mm) unless you have a reason for series 2 (0.2 · 0.6 · 1 mm).

How to use it in Inventor

  1. Draw the undercut as a profile in a sketch on a plane through the shaft's centre line and cut it with Revolve around that centre line.
  2. Put the dimensions you draw in as parameters (r, t1 and f; for type F also t2), so one change updates every shoulder. g is a guide value: do not draw the profile to it.
  3. Check the mating part. It needs a chamfer or countersink of at least a, so at the shoulder side a diameter of at least d1 + 2a. If a = 0, none is needed.
  4. On the drawing the designation is enough, for example “DIN 509 – F 0.8 × 0.3” (type, r and t1); the other dimensions follow from the table.

Sources

  • DIN EN ISO 18388:2020-01 / ISO 18388:2016, Technical product documentation (TPD) – Relief grooves – Types and dimensioning.
  • DIN 509:2022-12, Technical product documentation – Relief grooves – Types, dimensions and tolerances (not read).
  • DIN 509:2006-12, Technical drawings – Undercuts – Types and dimensions (withdrawn in 2020; source of the values).