Design Calculations · Gas spring

Gas springs for odd lid shapes and hinge positions

You have a lid, flap or door that should open with gas springs, but the online calculator only asks for width, depth and weight. Your hinge isn't on the edge, the lid is curved, or the door swings up instead of sideways. This page explains why those cases are different, what you need to measure and how to size them properly anyway.

Choose your situation

Why online calculators get stuck

Why online calculators get stuckHSPbPlhinge set insloped lidopen 75°
Sketch: why online calculators get stuck

Most online calculators assume a flat, rectangular lid with the hinge right on the back edge and the centre of gravity in the middle. Then width, depth and weight are enough. But what the spring really has to deliver follows from a moment balance about the hinge: the weight times the horizontal distance to the centre of gravity must be balanced by the spring force times the perpendicular distance from the hinge to the spring. Once the centre of gravity isn't in the middle, the hinge is offset, or the lid is L-shaped or curved, those distances are wrong, and so is the answer. Both distances also change as the lid opens.

Fields in the calculator

  • Centre of gravity S
  • Frame mounting point Pb
  • Lid mounting point Pl
  • Lid width (hinge to edge)
  • Handle
  • Opening angle α: closed 0°, open 75°
Calculate your own lid with the real centre of gravity and hinge position

Finding the centre of gravity

The centre of gravity is the point where you could hang the lid from a single string without it tilting. On a curved or built-up lid it often lies outside the material itself. Three ways to find it:

  • From your CAD model: Inventor and similar programs show mass and centre of gravity under physical properties (iProperties → Physical), provided materials are set correctly.
  • Hanging method: hang the lid from one corner and draw a plumb line; repeat from another corner. Where the lines cross is the centre of gravity.
  • Weighing method: rest the hinge side on a support and the front edge on a scale. The reading tells you how far the centre of gravity is from the hinge.

In the calculator you enter the centre of gravity as two distances from the hinge: along the lid and perpendicular to it, so a tall or slanted build counts as it should.

Fields in the calculator

  • Mass m
  • Centre of gravity S
Enter your centre of gravity in the gas spring calculator

Doors that open upwards

Doors that open upwardsHSPbPlopen ≈ 0°closed −90°
Sketch: doors that open upwards

A door hinged at its top edge hangs vertically when closed. In that position the centre of gravity is almost straight below the hinge, so little force is needed. As the door opens, the centre of gravity moves outwards and the moment grows; the load is highest when the door is horizontal, because the centre of gravity is then furthest from the hinge. Opening further, the load drops again. That's the opposite of an ordinary lid. A heavy door (the person asking had 90 kg) often needs two springs and a mounting point that gives the spring good leverage in the open position. Always check the full arc, not just the closed position.

This example uses a 30 kg door. A heavier hanging door, say 90 kg, needs more or stronger gas springs than this calculator covers; ask your supplier for advice.

Fields in the calculator

  • Mass m
  • Centre of gravity S
  • Frame mounting point Pb
  • Lid mounting point Pl
  • Opening angle α: closed −90°, open 0° to +10°
  • Number of springs n
Calculate a lift-up door: set the angles from closed to open

Flaps that open downwards

Flaps that open downwardsHSPbPlclosedopen
Sketch: flaps that open downwards

On a flap that folds down, like a drop-front desk or a loading flap, the spring doesn't lift: it brakes the weight so the flap doesn't fall. The spring is compressed as the flap drops. The weight always pulls the flap further open, so without a spring or brake it won't stay in an intermediate position. With a well-chosen gas spring it can stay put over a large part of its travel. Mounting points are chosen differently here, and the hand force needed to close the flap again matters a lot. In the calculator, enter a negative end angle (for example 0° to −80°) for a flap that opens downwards.

Fields in the calculator

  • Mass m
  • Centre of gravity S
  • Frame mounting point Pb
  • Lid mounting point Pl
  • Opening angle α from/to
  • Hand force open/close
Calculate a flap that opens downwards

Several springs under one lid

Several springs under one lidHSPbPln = 22 springs, 1 lid
Sketch: several springs under one lid

With several springs on the same hinge axis, the required force is shared by the number of springs, as long as they sit in identical positions. Mount them as mirror images on both sides with the same dimensions; otherwise one spring works harder than the other and the lid twists, loading hinges and springs. Always use identical springs (same force and length). Note: if your lid doesn't hinge but has to rise straight up (a parallel lift), none of this applies. The springs then push directly against the weight and you need guides to stop it tilting; our calculator doesn't cover that case.

Fields in the calculator

  • Number of springs n
  • Mass m
  • Centre of gravity S
  • Frame mounting point Pb
  • Lid mounting point Pl
Calculate the force per spring for 1, 2 or more springs

Fold-up beds and bed lifts

Fold-up beds and bed liftsHSPbPlbed uprightbed down
Sketch: fold-up beds and bed lifts

A bed is a heavy, large lid: frame plus mattress, and the mattress alone can weigh tens of kilos. A fold-up bed also often turns through 90° or more, so the load on the spring varies a lot over the stroke. Ready-made lift fittings are made for a certain weight and bed size; if they're too weak, adding more fittings only helps if they all pivot on the same axis and use identical springs. Weigh the frame and mattress first, find the centre of gravity, then calculate. For beds especially: a gas spring is not a safety component. Add a mechanical lock in the open position.

Fields in the calculator

  • Mass m
  • Centre of gravity S
  • Frame mounting point Pb
  • Lid mounting point Pl
  • Opening angle α from/to
  • Number of springs n
  • Hand force open/close
Calculate your fold-up bed or bed lift

Hand force and balance point

A well-tuned lid feels light both ways. If the spring is too strong, the lid flies open and you have to push hard to close it; too weak, and it sags or you have to lift it. The balance point is the angle where spring and weight cancel out: above it the lid stays open, below it the lid closes. Gas springs have friction, so opening and closing feel different. The calculator shows the hand force at the handle for opening and closing, and gives a range for the extension force F1 that keeps both within your limit. Because a spring pushes harder when compressed than when extended, F2 = progression × F1.

Fields in the calculator

  • Hand force open/close
  • Handle
  • Friction FR
Set your maximum hand force and see which F1 fits

When a calculation isn't enough

A calculation gives you a good first choice, not a guarantee. Gas spring force has a manufacturing tolerance of about ±10 %, and force goes up when warm and down when cold. Friction and wear change the feel over time. So always check the supplier's datasheet (lengths, stroke, F1 and progression), test with a real spring and consider one with a valve so you can still reduce the force. Where a falling lid or bed could hit someone, add a mechanical lock.

Start with a calculation, then check it in practice

Frequently asked questions

Can I use a webshop calculator for an L-shaped lid?

Only if your centre of gravity and hinge happen to match its assumptions. Usually not; enter the real centre of gravity instead.

How do I find the centre of gravity without CAD?

Use the hanging method, or weigh the front edge while the hinge side rests on a support (see above).

How many springs do I need?

The force is shared by the number of springs. Wide or heavy: two, mounted as mirror images with equal dimensions.

Why does my lid fly open or not stay up?

The spring is too strong, or the mounting points put the balance point in the wrong place. Look at the hand force over the full arc.

Can the calculator handle a lid that lifts straight up?

No, only lids and doors that rotate about a hinge.

Does this work for a door that opens upwards?

Yes: set the opening angles from closed (hanging vertically) to open and check the full arc.