Design Calculations · Gas spring

Gas spring calculator: force, length and mounting points

Force, progression, friction and tolerance in one table: stated where published, clearly marked where not.

Calculator

Enter the mass, centre of gravity and mounting points; the calculator gives the force per spring over the whole opening arc, a suggested F1 and the lengths.

Dimensions in mm from the hinge H. x runs towards the closed flap, y upwards. Points on the flap (S and Pl) are given in flap coordinates: u along the flap, v perpendicular to it; they rotate with α. α is measured from horizontal, closed = 0°, positive = opens upwards, negative = opens downwards.

Scale drawing of flap, hinge and gas spring

Drawn to scale from your input. Geometry only; the calculator works out the force.
Number of springs n

Default 1.35, as in the worked example (Bansbach: about 33 %).

Result

Range for F1

—

Any F1 in this range meets your hand force for opening and closing.

F1 per spring

—

Spring force when fully extended (lid open).

F2 per spring

—

Force when the spring is compressed: F2 = progression × F1.

Hand force at the handle

How much force you want to apply at the handle on the edge to open.

How much force you want to apply to close.

The handle is at the edge; you push or pull perpendicular to the lid.

Optional. Default: edge.

difference compress – extend; default 60 N

Largest hand force to open
—
Largest hand force to close
—
Balance angle(s)
—

At a balance angle the lid stays put on its own. There can be more than one, or none.

Hand force at the handle

Spring force per spring

  • Opening (solid)
  • Closing (dashed)
  • Chosen hand force
  • Balance point
  • Balance angle (dotted line through both charts)
  • Extending (solid)
  • Compressing (dashed)
  • Friction band
  • F1 and F2, as on the cards

Plus: your hand acts in the lid’s opening direction. Minus: your hand acts in the closing direction. Zero: the lid stays put on its own.

Hand force at the handle over the opening angle α. Spring force per spring over the same opening angle α, at the suggested F1. Friction lies between extending and compressing.
Show the values as a table
Angle αOpening (N)Closing (N)Spring extending (N)Spring compressing (N)
Extended length Lu
—
Compressed length Li
—
Stroke
—

Choose a spring with about 10 mm extra stroke as reserve (ACE, Hahn). Formula and sources

Geometry

8/19 gas springs and gas struts compared across brands

About this comparison and how to read the table

This page helps you pick a spring once you know the force you need (for a rough hand check, see the worked example). Manufacturers and shops rarely give the full specification in one place: progression, friction and force tolerance are often missing.

This page compares six suppliers of the common 8/19 size (8 mm rod, 19 mm body) for 100 mm and 200 mm stroke. They are not six independent manufacturers: gasveerexpert sells the Newtonic brand, made by Hahn according to the shop, which also calls Hahn “a Stabilus company”; the manufacturer behind gasveerwinkel is not stated. Where a supplier does not publish a value, the table says so; our own estimates are marked.

How to read the table

stated = published by the manufacturer or sellerderived = calculated by us from published figuresestimated = our own estimate, see notes 1 and 6not published = the supplier does not publish this value

Jump to: what the values mean · table 100 mm · table 200 mm · worked example · temperature · mounting and safety

Stroke 100 mm

SupplierArticleF1 availableProgression F2/F1 · F2 at F1 = 400 NExtended / compressed length ³Measuring basis · length tolerance ³Max. stroke (series)End fittingsStainless · dampingFriction FR ²Force tolerance ⁶Temperature rangePrice per piece, € excl. VAT, spring only ⁴Lead time / stock ⁴Business only ⁴Sources
gasveerwinkel.nlshop, own range; manufacturer not statedGasveer 8-19 slag 100 (product name), SKU G010810004550–800 N, mostly 10 N steps1.42 (41.6 %) statedF2 ≈ 566 N derived245 / 145 mmbare spring with M8 threads; reference points not stated; tolerance not publishednot publishedM8×1.25 thread both ends; fittings sold separatelystainless 304/316 as separate products; damping not publishednot publishednot publishedtypical ±10 % estimated, note 6not published€38.06€46.05 incl. 21 % VAT250+ in stock; 1–3 working days (shop banner)no: consumer webshop (Thuiswinkel Waarborg)product page
gasveerexpert.nlbrand Newtonic; manufacturer per shop: Hahn (Protempo)GS277100100–250 N1.20–1.35 estimated400 N not offered derived277 / 177 mmbare spring with M8 threads; reference points not stated; differs from Hahn standard 270 mm; tolerance not publishednot publishedM8 thread; fittings sold separatelystainless versions offered (shop text); damping not publishednot publishednot publishedtypical ±10 % estimated, note 6not published€39.21€47.45 incl. 21 % VAT3–5 working daysnot publishedproduct page
StabilusLift-O-Mat HD 8-19; price from reseller ap.co.at084190 (700 N, eye–eye); 500/600/800 N: 084174 / 084182 / 094706500, 600, 700 or 800 N (eye–eye at this stroke); series 100–800 N1.35 (≈, series) stated400 N not offered eye–eye; at 500 N: F2 ≈ 675 N derived285–285.5 / 185–185.5 mmeye centre to eye centre (eyes are part of the spring); ±2 mm stated250 mm statedeyes Ø8.1 (+0.3) mm, 5 mm thick; ball-socket versions under other numbershydraulic damping on extension; stainless not in this catalogue≤ 60 N (series maximum FR, not per article) stated±3 N ±5 % (min.) to ±10 % (max.), Stabilus general tolerance stated−30 to +80 °C stated€33.20listed excl. VAT; 084190, 700 N15 in stock; 3–27 working days (ap.co.at)not publishedStabilus catalogue (PDF); reseller page
Bansbach easyliftprice from the North American web storeB0N0F50-100-247/xxxN (xxx = force in N)30–700 N, 5 N steps1.33 (approx. 33 %, series) statedF2 ≈ 532 N derived247 / 147 mmbare spring with M8 threads; store does not state reference points (catalogue EL2: without eyes and threads); ±2.5 mm300 mm statedM8×1.25 thread both endsstainless (AISI 304 or 316L) and several damping options in the type code statednot published+40 / −20 N or ±5–7 % (which one applies is not stated, note 6) stated−30 to +80 °C stated€39.96US$45.03 at ECB rate 1.1269not publishednot publishedstore page; Bansbach catalogue (PDF)
ACEGS-19 with valve, filled to orderGS-19-10050–700 N, filled to order1.35 (≈), assuming 945 N is F2, note 5 derivedF2 ≈ 540 N derived264 / 164 mmnot stated (product table: “L extended”); tolerance not published300 mm (max. 450 N at 300 mm) statedinterchangeable threaded end fittings, zinc-plated steelend damping approx. 20 mm; stainless not on this pagenot publishednot publishedtypical ±10 % estimated, note 6−20 to +80 °C statedon requestno public pricenot publishedyes: delivers only to business customers with a valid VAT IDproduct page
Hahn Gasfedernmade to ordertype G 08-19, stroke 10050–800 N1.30 (30 %, series) statedF2 ≈ 520 N derived270 / 170 mmstandard length 2 × stroke + 70 of the bare spring with M8 threads; ±2 mm500 mm statedM8 thread both ends; fittings sold separatelyAISI 303/304 and 316L/316Ti versions; with or without damping statednot published±10 %, at least ±3 N stated−20 to +80 °C statedon requestno public pricenot publishedmade to ordernot publishedHahn catalogue (PDF); product family page (no 8/19 data)

Scroll sideways to see all columns; the first column stays in place.

Stroke 200 mm

SupplierArticleF1 availableProgression F2/F1 · F2 at F1 = 400 NExtended / compressed length ³Measuring basis · length tolerance ³Max. stroke (series)End fittingsStainless · dampingFriction FR ²Force tolerance ⁶Temperature rangePrice per piece, € excl. VAT, spring only ⁴Lead time / stock ⁴Business only ⁴Sources
gasveerwinkel.nlshop, own range; manufacturer not statedGasveer 8-19 slag 200 (product name), SKU G010820004550–800 N, mostly 10 N steps1.37 (37.0 %) statedF2 ≈ 548 N derived445 / 245 mmbare spring with M8 threads; reference points not stated; tolerance not publishednot publishedM8×1.25 thread both ends; fittings sold separatelystainless 304/316 as separate products; damping not publishednot publishednot publishedtypical ±10 % estimated, note 6not published€37.46€45.33 incl. 21 % VAT250+ in stock; 1–3 working days (shop banner)no: consumer webshop (Thuiswinkel Waarborg)product page
gasveerexpert.nlbrand Newtonic; manufacturer per shop: Hahn (Protempo)GS481200100–900 N (14 options); 900 N is above Hahn’s 800 N maximum for G 08-19, note 51.22–1.33 estimatedF2 ≈ 488–532 N estimated481 / 281 mmbare spring with M8 threads; reference points not stated; differs from Hahn standard 470 mm; tolerance not publishednot publishedM8 thread; fittings sold separatelystainless versions offered (shop text); damping not publishednot publishednot publishedtypical ±10 % estimated, note 6not published€40.45€48.95 incl. 21 % VAT3–5 working daysnot publishedproduct page
StabilusLift-O-Mat HD 8-19; price from reseller hinscha.com084638 (500 N, eye–eye); 100–800 N: 084573 … 094889100–800 N (eye–eye): steps of 50 N up to 400 N, then 100 N1.35 (≈, series) statedF2 ≈ 540 N derived485–485.5 / 285–285.5 mmeye centre to eye centre (eyes are part of the spring); ±2 mm stated250 mm statedeyes Ø8.1 (+0.3) mm, 5 mm thick; ball-socket versions under other numbershydraulic damping on extension; stainless not in this catalogue≤ 60 N (series maximum FR, not per article) stated±3 N ±5 % (min.) to ±10 % (max.), Stabilus general tolerance stated−30 to +80 °C stated€75.49listed excl. VAT; 084638, 500 Nnot in stock; ±11–13 weeks (hinscha.com)not publishedStabilus catalogue (PDF); reseller page
Bansbach easyliftprice from the North American web storeB0N0F40-200-455/xxxN (xxx = force in N)30–700 N, 5 N steps1.33 (approx. 33 %, series) statedF2 ≈ 532 N derived455 / 255 mmbare spring with M8 threads; store does not state reference points (catalogue EL2: without eyes and threads); ±2.5 mm300 mm statedM8×1.25 thread both endsstainless (AISI 304 or 316L) and several damping options in the type code statednot published+40 / −20 N or ±5–7 % (which one applies is not stated, note 6) stated−30 to +80 °C stated€49.91US$56.24 at ECB rate 1.1269not publishednot publishedstore page; Bansbach catalogue (PDF)
ACEGS-19 with valve, filled to orderGS-19-20050–700 N, filled to order1.35 (≈), assuming 945 N is F2, note 5 derivedF2 ≈ 540 N derived464 / 264 mmnot stated (product table: “L extended”); tolerance not published300 mm (max. 450 N at 300 mm) statedinterchangeable threaded end fittings, zinc-plated steelend damping approx. 20 mm; stainless not on this pagenot publishednot publishedtypical ±10 % estimated, note 6−20 to +80 °C statedon requestno public pricenot publishedyes: delivers only to business customers with a valid VAT IDproduct page
Hahn Gasfedernmade to ordertype G 08-19, stroke 20050–800 N1.30 (30 %, series) statedF2 ≈ 520 N derived470 / 270 mmstandard length 2 × stroke + 70 of the bare spring with M8 threads; ±2 mm500 mm statedM8 thread both ends; fittings sold separatelyAISI 303/304 and 316L/316Ti versions; with or without damping statednot published±10 %, at least ±3 N stated−20 to +80 °C statedon requestno public pricenot publishedmade to ordernot publishedHahn catalogue (PDF); product family page (no 8/19 data)

Scroll sideways to see all columns; the first column stays in place.

Your calculation as PDF + Excel

Not for sale yet, you pay nothing. Click if you would pay €5 for it; that only counts your interest.

We only count this click: no name, email, IP address or cookies.

Not available yet: we’re checking whether there’s demand for this. Thanks!

Choosing the gas strut mounting points

Hatch or lid: hinge, centre of gravity and mounting points
Drawing 3: hatch or flap with hinge H, centre of gravity S, distance L, mounting points Pb and Pl and the perpendicular distance r⊥ to the spring’s line of action.

The gas spring runs from a fixed point on the frame (Pb) to a point on the lid (Pl). The larger the perpendicular distance r⊥ from the hinge H to that line, the less force each spring needs — but in every position the spring length must stay between its compressed (Li) and extended (Lu) length.

How many newtons does my gas strut need?

Convert the mass to newtons (1 kg ≈ 9.81 N) and take moments about the hinge: F ≈ m·g·L / (n·r⊥). A gas spring pushes harder when compressed (F2) than when extended (F1), so work back to F1 — the value springs are ordered by.

Worked example: from required force to F1

Example: with these inputs the calculator gives this result.

Inputs: lid 10 kg, centre of gravity S at u = 250 mm, v = 0 mm; Pb at x = 60, y = −300 mm; Pl at u = 120, v = 0 mm; α from 0° to 80°; 2 springs; progression 1.35; hand force 20 N to open and 30 N to close; lid width 500 mm (handle at the edge); friction 60 N.

Outcome per spring: F1 between 75 N (7.7 kg) and 102 N (10.4 kg), suggested F1 89 N (9.1 kg), F2 120 N (12.2 kg); Lu 420.0 mm, Li 305.9 mm, stroke 114.1 mm. Largest hand force 14 N to open, 22 N to close; balance angle(s): none. The calculator starts with these same inputs.

Check the whole opening arc, leave about 10 mm of stroke unused and confirm with the supplier. Manufacturers offer calculation help, e.g. the ACE calculation tools.

Length, stroke and force curve (F1/F2)

Show explanation

What do the values mean?

Drawing 1 uses a Stabilus 8/19 spring with 100 mm stroke; the graph and the cut-away are schematic.

Gas spring extended and compressedThe same Stabilus 8/19 gas spring with 100 mm stroke drawn twice, aligned at the body end: extended 285 mm and compressed 185 mm, measured eye centre to eye centre. The difference is the stroke of 100 mm. Body diameter 19 mm, rod diameter 8 mm.extended length 285 mmcompressed length 185 mmstroke 100 mm = 285 − 185ExtendedCompressedbody Ø19rod Ø8measuring point:eye centre / connection centreStabilus 8/19, stroke 100 mm (e.g. 084174),eye centre to eye centre, roughly to scale Gas spring extended and compressedThe same Stabilus 8/19 gas spring with 100 mm stroke drawn twice, aligned at the body end: extended 285 mm and compressed 185 mm, measured eye centre to eye centre. The difference is the stroke of 100 mm. Body diameter 19 mm, rod diameter 8 mm.extended length 285 mmstroke 100 mm = 285 − 185compressed length 185 mmExtendedCompressedbody Ø19rod Ø8measuring point: eye centre / connection centreStabilus 8/19, stroke 100 mm (e.g. 084174),eye centre to eye centre, roughly to scale
Drawn after the Stabilus Lift-O-Mat HD 8/19 with 100 mm stroke (e.g. 084174): 285 mm extended and 185 mm compressed, measured eye centre to eye centre (catalogue tolerance ±2 mm). Some suppliers give the length of the bare spring without end fittings (see the column “Measuring basis” and note 3), so compare lengths only on the same basis.
Force over the strokeForce against stroke from extended (0) to compressed (s). The upper curve is the compression force when the rod is pushed in, with F3 and F4. The lower curve is the extension force when the spring pushes out, with F1 at 5 mm before the extended end and F2 at 5 mm before the compressed end. Friction FR is the gap between the curves at the 5 mm point, FR = F3 − F1. Progression is F2 divided by F1.force F0sextendedcompressedstroke →55compression: pushing in →← extension: spring pushes outF1F2F3F4FRFR = F3 − F1 (friction)progression = F2 / F1measured statically at 20 °C
According to the common catalogue definition (Stabilus, Bansbach). The direction of travel matters: pushing the rod in follows the upper curve (F3 → F4), letting the spring push out follows the lower curve (F2 → F1). F1 and F2 are therefore both on the lower curve, each 5 mm from an end position. The hydraulic end damping in the last part of the extension stroke is not drawn.
In practice: a lid opens along the lower curve and closes along the upper one. The band between them is why a lid can stay put part-way, and why closing by hand takes about FR more force than the spring delivers when opening. Friction depends on speed and temperature, and after a long standstill the first stroke needs extra breakaway force (Hahn).
Where the force comes fromCut-away of a gas spring: nitrogen gas at pressure p fills the cylinder; the piston has an orifice so the pressure is the same on both sides. The net force is the pressure times the rod cross-section A of about 50 square millimetres. When the rod moves in, the gas volume shrinks, the pressure rises and so does the force.N₂ gaspressure pA = π·8²/4 ≈ 50 mm²F ≈ p·Apiston with orificeoilrod inrod in → gas volume V ↓ → p ↑ → F ↑Boyle: p·V ≈ constant
The piston has a small orifice, so the gas pressure p is equal on both sides and only acts on the rod cross-section: F ≈ p·A, less friction when extending. Example: 400 N needs p ≈ 400 / 50.3 ≈ 8 N/mm² = 8 MPa ≈ 80 bar. When the rod moves in it takes up gas volume, so the pressure and the force rise towards the compressed end. A few ml of oil lubricates the seal and, with the rod pointing down, damps the end of the extension stroke.
  • F1: The nominal force: the extension force (spring pushing out), according to the common catalogue definition measured statically at 20 °C, 5 mm before the fully extended end position (some damped types: 10 mm).
  • F2: The extension force measured 5 mm before the fully compressed end position, so nearly the highest force with which the spring pushes out (the last 5 mm still add a little).
  • Progression F2/F1: How much the force rises over the stroke: 1.35 means F2 is 35 % higher than F1, so F1 = 400 N gives F2 ≈ 540 N.
  • Friction: The gap between the compression and the extension curve, defined by Stabilus as FR = F3 − F1; where it is not published we give no value, but as a rough estimate expect FR ≈ 10–20 % of F1 and, for 8/19, not more than about 60 N (note 2).
  • Stroke: The distance the rod travels, equal to extended length minus compressed length.
  • Extended length: The overall length with the rod fully out, measured between the measuring points.
  • Compressed length: The overall length with the rod fully in; in the tables it is calculated as extended length minus stroke (note 3).
  • Measuring points: The points the length is measured between, usually eye centre to eye centre (connection centre), but some suppliers give the bare spring without end fittings, so check the drawing (note 3).
  • Force tolerance: The allowed deviation of the actual F1 from the nominal value, for example ±10 % or +40 / −20 N (note 6).
  • Temperature range: The range in which the spring may be used, for example −30 to +80 °C; this is separate from how much the force changes with temperature (see Temperature and force).

Gas struts for hatches, flaps, lids and trailers

Whether a flap opens upwards or downwards changes the spring’s job: opening upwards, the gas strut lifts the weight and the load peaks when closed (α = 0°); opening downwards, it holds the weight back. Always check the full opening arc, from closed to fully open.

Show explanation
Upward-opening flap compared with downward-opening flap
Drawing 4: flap opening upwards versus flap opening downwards.

Temperature and mounting

Show explanation

Temperature and force

The gas force is roughly proportional to the absolute temperature: F(T) ≈ F20 · (T + 273) / 293, with T in °C. That is about 3.4 % per 10 °C; suppliers give 3–3.5 % (Hahn) and about 3.3 % (Bansbach).

Example: at −10 °C the force is about 10 % lower (263 / 293 ≈ 0.90), at +50 °C about 10 % higher (323 / 293 ≈ 1.10).

The temperature range in the table (−20 or −30 to +80 °C) is something else: it says where the spring may be used, not how much its force changes.

Mounting and safety

  • Mount with the rod pointing down in the rest position, so the seal stays lubricated and the end damping works (Hahn, ACE).
  • Leave about 10 mm of stroke unused (LDA) and provide an external end stop (ACE, Hahn).
  • Axial load only: no side load, bending or canting (Hahn). Maximum speed 300 mm/s (Hahn).
  • Gas springs are not safety components (Hahn): where failure could injure someone, for example with an overhead hatch, add a mechanical lock or prop.
  • Internal pressure up to 160 bar without load (Hahn): never drill, weld, heat or open a spring, and do not paint or damage the rod.
  • A force loss of 5 % in the first 12 months and 10 % in 4 years is normal; more than 50,000 cycles is possible (Hahn).
  • After long storage the first stroke needs extra breakaway force; this levels out after one or two cycles (Hahn).

Sources: Hahn catalogue, technical regulations; ACE GS-19; LDA guide (PDF).

Frequently asked questions

What size gas strut do I need?

Four things decide it: the force F1 per spring, the stroke, the extended length Lu and the end fittings (thread or eye). Work out the force from the mass m, the distance L and the mounting points first, then pick a size that fits — the 8/19 table below shows what suppliers publish.

How do I calculate gas spring force in newtons?

Find the mass m, the centre of gravity S and the horizontal distance L from hinge H to S. Choose the mounting points Pb and Pl and measure the perpendicular distance r⊥ from H to the spring; then F ≈ m·g·L / (n·r⊥). L and r⊥ change with the opening angle α, so check several positions, not just closed.

How many newtons does my gas spring need?

Use F ≈ m·g·L / (n·r⊥): a 10 kg flap with L = 250 mm, two springs and r⊥ = 50 mm needs about 245 N per spring when closed. Divide by the progression (for example 1.35) to get F1, and allow a margin for temperature and force tolerance (±10 %), as in the worked example.

Where should I mount a gas strut?

Place Pb on the frame and Pl on the lid so that, when closed, the rod points downwards and the spring is loaded only along its axis — no side load or misalignment. A larger r⊥ means less force but more stroke. Gas springs are not safety components: where a falling lid could hurt someone, add a mechanical lock or prop.

How do I measure gas spring length and stroke?

Measure the distance between Pb and Pl with the lid closed and fully open: the difference is the stroke you need, plus about 10 mm in reserve. The longer distance must match the extended length Lu. Check how length is measured: some manufacturers quote eye centre to eye centre, others the bare spring without fittings.

Are gas springs constant force?

See What do the values mean?

Gas spring or gas strut: what is the difference?

“Gas spring” and “gas strut” describe the same part: a sealed cylinder whose gas pressure pushes the rod out. This page uses “gas spring” for the push type throughout.

Should the rod point up or down when mounted?

See Mounting and safety.

One or two gas struts for a lid?

The formula divides the force by the number of springs n. If you use two, mount them identically on both sides so they share the load equally.

Can I download the calculation as PDF or Excel?

Not yet: we’re checking whether there’s demand for this. The button on this page only counts your click.

Notes

  1. Progression estimate (Boyle). With p·V constant (isothermal), F2/F1 ≈ V1 / (V1 − A·s): A is the rod cross-section (π·8²/4 ≈ 50 mm²), s the stroke and V1 the gas volume at full extension. We estimate V1 from the body length, an assumed inner diameter of about 16.6 mm, the piston package and roughly 2 ml of oil; those unknowns give the band. A check against a published value: gasveerwinkel 100 mm, model ≈ 1.44, published 1.42. Hahn publishes 30 % for its G 08-19 series; the gasveerexpert springs are made by Hahn according to the shop, but their lengths differ from the Hahn standard (note 5), so we keep our own band.
  2. Friction. FR = F3 − F1 is published only by Stabilus for this size: FR max 60 N for the whole 8/19 series (100–800 N), a series maximum and not a value per article. The other suppliers publish no figure, so the table says “not published”. Rough estimate (our rule of thumb, not a supplier value): FR ≈ 10–20 % of F1, capped at about 60 N for 8/19; for example F1 = 100 N → 10–20 N, 200 N → 20–40 N, 400 N → 40–60 N, 800 N → about 60 N. Basis: Misumi gives the internal sliding friction as about 0.1 × the theoretical force, and the gap between the compression and extension curves can be up to twice that; the cap is the Stabilus series maximum. Real friction depends on seal, lubrication, speed, temperature and standstill time.
  3. Lengths and measuring basis. Extended length as published; compressed length = extended length − stroke (calculated). Reference points differ: Stabilus measures eye centre to eye centre, with the eyes part of the spring. Hahn gives the standard length 2 × stroke + 70 of the bare spring with M8 threads. The Bansbach catalogue measures its installation length EL2 without eyes and threads (minimum 2 × stroke + 48, so 248 / 448 mm), while the US store lists 247 / 455 mm without saying how it measures. The other sellers do not state their reference points. With M8 threads each fitting adds its own length, so compare eye-to-eye only after adding the fittings. Length tolerance from the catalogues: Stabilus ±2 mm, Hahn ±2 mm, Bansbach ±2.5 mm.
  4. Prices, lead time and business-only. Checked on 6 October 2026. Basis: euros excluding VAT, per piece, spring only, before shipping. Dutch shop prices include 21 % VAT and were divided by 1.21. ap.co.at (Austria) and hinscha.com (Belgium) list prices excluding VAT; for Stabilus the eyes are part of the spring. Bansbach: US-store price converted at the ECB euro reference rate of 6 October 2026, 1 EUR = 1.1269 USD (ECB), excluding US sales tax, shipping and import duties. Fittings for M8 springs are extra (two needed): gasveerwinkel M8 eye 16 mm €2.36 incl. VAT (€1.95 excl.); gasveerexpert flat M8 eye €4.61 incl. VAT (€3.81 excl.) or milled M8 eye Ø8.1 €5.05 (€4.17 excl.), as listed on its product pages. Lead time, stock and business-only are filled in only where the seller publishes them.
  5. Series values and row remarks. Bansbach, Hahn and Stabilus publish one progression figure per 8/19 series, not per article. ACE: 1.35 = 945 / 700 N, assuming that “compressed up to 945 N” is F2 at the 700 N maximum; ACE does not say whether it is F2 or the compression force F4. gasveerexpert 200 mm lists up to 900 N, above the 800 N that Hahn gives for G 08-19, and its lengths 277 / 481 mm differ from the Hahn standard 270 / 470 mm, so it may not be a standard G 08-19. Stabilus at 100 mm stroke (eye–eye) comes only in 500–800 N; 084190 and 094706 are 285.5 mm long. Stabilus gives the body as Ø19 with tolerance −1 mm (so 18–19 mm), which is why some resellers list 18 mm.
  6. Force tolerance. Where a supplier publishes nothing, “typical ±10 %” is our estimate based on the published values of others: Hahn ±10 %, at least ±3 N; Stabilus ±3 N ±5 % (minimum) to ±10 % (maximum) (Stabilus IndustryLine catalogue); Bansbach +40 / −20 N or ±5–7 %. The Bansbach catalogue does not say which of its two rules applies; note that +40 / −20 N at F1 = 200 N is +20 / −10 %.
Disclaimer: Values are partly estimated and taken from public catalogues and product pages, which can change. Always check force, length, end fittings and tolerances with the supplier before you design or order. Shop links are plain links; we receive nothing for them.

Sources for the texts added on 20 October 2026 (mounting points, newtons, applications and the FAQ): the worked example and the table on this page; Hahn catalogue (pdf): F1 5 mm before end of stroke, ±10 %, progression, push and tension springs, rod down, axial load only, not a safety component; Stabilus catalogue (pdf): length eye centre to eye centre; Bansbach catalogue (pdf): progression about 33 %; ACE (GS-19): about 10 mm stroke reserve. That a downward-opening flap is braked by the spring and that a larger r⊥ needs more stroke follows from geometry (moments about the hinge and the Pb–Pl distance over the opening arc); we checked both with our own calculation model.

Calculator: in every position α (1° steps) the moments about the hinge balance: n·F·r⊥(α) = m·g·L(α), so F(α) = m·g·L(α) / (n·r⊥(α)); L and r⊥ follow from the coordinates of S, Pb and Pl. Lu and Li are the largest and smallest Pb–Pl distance over the angle range, stroke = Lu − Li. The spring force runs from F1 (extended) to F2 = progression · F1 (compressed); this is a simplification: linear force curve. The required F1 is the largest value of F(α) / (1 + (progression − 1)·(Lu − l(α))/(Lu − Li)). Hand force (at the lid edge, r = lid width): opening F_hand = (m·g·L − n·(F_spring − FR/2)·r⊥) / r, closing F_hand = (n·(F_spring + FR/2)·r⊥ − m·g·L) / r, with F_spring running from F1 to F2 over the stroke and FR = F3 − F1 the friction band per spring (for a downward-opening flap, or a spring that compresses while opening, the signs follow). Both must stay ≤ your hand force in every position; this gives the allowed F1 range, and the suggested F1 is its midpoint. Friction: Stabilus standard catalogue, FR max 50/60/80 N for Ø6/15, Ø8/19 and Ø10/22–14/28. Not included: damping, temperature, the spring’s own weight and the stroke reserve of about 10 mm. Sources: statics (moment balance); progression and tolerance see above (Bansbach, Hahn).