Design Calculations · Bearing fit ISO 286

Bearing fit: shaft and housing (ISO 286)

Load case and size → recommended shaft and housing class, limit deviations and clearance or interference

mm
mm
The shaft diameter at the bearing, over 0.6 up to 500 mm.
Optional. Fill it in to get the housing fit. It must be larger than the bore.
Common bores

Fills in the bore (and a common outside diameter).

Which ring turns relative to the load?
Load size
Load P as a part of the dynamic load rating C of the bearing: light up to 5 %, normal 5 to 10 %, heavy over 10 %.
Bearing type
Roller: cylindrical or tapered. Spherical roller bearings are not covered; ask the bearing maker.
Axial movement of the ring with the fixed load
Outer ring in the housing: a floating bearing slides, a locating bearing is fixed.
Choose another class to see its fit.
—

Recommendations: Koyo table, gaps compared with SKF, NSK, Schaeffler and Timken. Limit deviations: ISO 286. Bearing: ISO 492 Normal class.

About the values

The classes are suggestions for bearings of the Normal tolerance class on solid steel shafts and in cast iron or steel housings. The deviations come from ISO 286 and the fit uses the mean diameter of the bearing (ISO 492). Interference lowers the internal clearance of the bearing; surface roughness makes the real interference slightly smaller.

Inventor: Manage › Parameters, or straight into the dimension and tolerance fields of your sketch. Copied numbers always use a decimal point.

Section of a bearing on a shaft in a housing: the shaft diameter d with its class (for example k5) at the inner ring, the outside diameter D with the housing class (for example H7) at the outer ring. Dd housingshaft outer ringinner ring
Shaft fit at the bore d, housing fit at the outside diameter D
Enter the bearing bore: the fit appears here.

The fits are recommendations from public bearing tables and are meant as an aid. Check them with your bearing maker, and check your own drawing. You remain responsible for your design.

Details: explanation, Inventor and sources

How to read this

Which ring turns. The ring that turns relative to the load needs a tight fit, or it creeps and wears. With a turning shaft and a load in a fixed direction, that is the inner ring: tight on the shaft (for example k5 or m6), and the outer ring in the housing can be looser (H7). With a fixed axle and a turning outer ring (a wheel), the outer ring needs the tight fit (N7 or P7) and the inner ring a looser one (g6 or h6). With a load that changes direction, vibrates or is unbalanced, both rings get a tight fit.

Load size. The heavier the load, the tighter the fit. The load is the equivalent dynamic load P against the dynamic load rating C.

Reading the fit. Shaft fit = bearing bore minus shaft; housing fit = housing bore minus bearing outside diameter. A minus sign means interference. For a bearing with a tight fit, the interference reduces the internal clearance; check the bearing clearance class (for example C3) with your bearing maker.

Not covered. Precision bearings, hollow shafts, light-alloy housings, large temperature differences between shaft and housing, spherical roller bearings, tapered bores (adapter sleeves), thrust bearings. Use the maker's catalogue for those.

How to use it in Inventor

  1. Click the shaft diameter and copy the nominal value. In the tolerance settings of that dimension, paste the upper and lower deviation (they use a decimal point, as Inventor expects).
  2. Do the same for the housing bore. For a drawing it is often enough to give the class, for example Ø 50 k5 and Ø 90 H7.
  3. Put the diameters in parameters, so one change updates the shaft, the housing and the bearing seat.

Sources

  • JTEKT/Koyo, Basic Bearing Knowledge, Recommended fits, Tables 9-4 (1) and (2): shaft and housing classes for radial bearings, per load case, load size and diameter (public web page). For ball bearings under heavy load, and for J7, this table is not used or has no row; see the notes on the page.
  • Where the Koyo table has no row, other public bearing maker tables were compared: SKF Rolling bearings (17000, 2018), tables 5 and 6; NSK Rolling Bearings (E1102m), table 9.2; Schaeffler, shaft tolerances for radial bearings; Timken Engineering Manual, tables 59 and 74. A class is filled in only where at least two of them agree (ball bearings over 280 mm under normal load: n6; roller bearings over 200 mm under heavy load: r6). Elsewhere the page gives no recommendation and says why. The makers draw the lines between light, normal and heavy load slightly differently. The r6 limits (ISO 286-2) were checked against three public tables and the SKF catalogue.
  • ISO 286-1 and ISO 286-2, limits and fits: tolerance grades IT5–IT9 and the fundamental deviations of g, h, j, js, k, m, n, p, r (shafts) and H, J, K, M, N, P (housings), up to 500 mm. Checked against known table values.
  • ISO 492:2014, radial bearings, Normal class: deviations of the mean bore and outside diameter. Checked against a public bearing maker's tolerance table (the standard text itself was not read).